View MIG400Q2CMB1X_1068280.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIG400Q2CMB1X
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
MIG400Q2CMB1X (1200V/400A 2in1)
High Power Switching Applications Motor Control Applications
* * * * * * Integrates inverter power circuits and control circuits (IGBT drive unit, units for protection against short-circuit current, overcurrent, undervoltage and overtemperature) into a single package. The electrodes are isolated from the case. Low thermal resistance VCE (sat) = 2.4 V (typ.) UL recognized: File No.E87989 Weight: 380 g (typ.)
Equivalent Circuit
1 2 3 4 5 6 7 8
FO GND IN VD
FO GND IN VD
GND VS
OUT
GND VS
OUT
E2 C2/E1 1. 5. FO (L) FO (H) 2. 6. GND (L) GND (H) 3. 7. IN (L) IN (H)
C1
4. 8.
VD (L) VD (H)
1
2001-11-13
MIG400Q2CMB1X
Package Dimensions: TOSHIBA 2-123C1A
Unit: mm
1. 5.
FO (L) FO (H)
2. 6.
GND (L) GND (H)
3. 7.
IN (L) IN (H)
4. 8.
VD (L) VD (H)
2
2001-11-13
MIG400Q2CMB1X
Signal Terminal Layout
Unit: mm
1. 5.
FO (L) FO (H)
2. 6.
GND (L) GND (H)
3. 7.
IN (L) IN (H)
4. 8.
VD (L) VD (H)
3
2001-11-13
MIG400Q2CMB1X
Maximum Ratings (Tj = 25C)
Stage Supply voltage Collector-emitter voltage Inverter Collector current Forward current Collector power dissipation Junction temperature Control supply voltage Input voltage Control Fault output voltage Fault output current Operating temperature Storage temperature Module Isolation voltage Screw torque (terminal) Screw torque (mounting) AC 1 min M6 M5 FO-GND terminal FO sink current Tc = 25C, DC Tc = 25C, DC Tc = 25C 3/4 VD-GND terminal IN-GND terminal Characteristics Condition P-N power terminal 3/4 Symbol VCC VCES IC IF PC Tj VD VIN VFO IFO Rating 900 1200 400 400 3780 150 20 20 20 10 -20~+100 -40~+125 2500 3 3 Unit V V A A W C V V V mA C C V Nm Nm
3/4 3/4
Tc Tstg VISO 3/4 3/4
Electrical Characteristics
1. Inverter stage
Characteristics Collector cut-off current Symbol ICEX Test Condition VCE = 1200 V VD = 15 V IC = 400 A VIN = 15 V (R) 0 V Tj = 25C Tj = 125C Tj = 25C Tj = 125C Min 3/4 3/4 3/4 3/4 3/4 3/4 VCC = 600 V, IC = 400 A VD = 15 V, VIN = 15 V 0 V Tj = 25C, Inductive load (Note 1) 3/4 3/4 3/4 3/4 Typ. 3/4 3/4 2.4 2.8 2.4 2.0 0.5 0.3 1.6 0.3 Max 1 10 2.8 3/4 2.8 3.0 3/4 3/4 2.5 3/4 ms V V Unit mA
Collector-emitter saturation voltage Forward voltage
VCE (sat) VF ton tc (on)
IF = 400 A, Tj = 25C
Switching time
trr toff tc (off)
Note 1: Switching time test circuit & timing chart
4
2001-11-13
MIG400Q2CMB1X
2. Control stage (Tj = 25C)
Characteristics Control circuit current Input on signal voltage Input off signal voltage Protection Fault output current Normal Overcurrent protection trip level Short-circuit protection trip level Overcurrent cut-off time Overtemperature protection Control supply under voltage protection Fault output pulse width Trip level Reset level Trip level Reset level High side Low side Symbol ID (H) ID (L) VIN (on) VIN (off) IFO (on) IFO (off) OC SC toff (OC) OT Case temperature OTr UV UVr tFO VD = 15 V 3/4 VD = 15 V Test Condition Min 3/4 3/4 1.4 2.2 8 3/4 640 640 3/4 110 3/4 11.0 12.0 1 Typ. 13 13 1.6 2.5 10 3/4 3/4 3/4 5 118 98 12.0 12.5 2 Max 17 17 1.8 V 2.8 12 mA 0.1 3/4 3/4 3/4 125 3/4 12.5 V 13.0 3 ms C A A ms Unit mA
VD = 15 V
VD = 15 V VD = 15 V, Tj < 125C = VD = 15 V, Tj < 125C = VD = 15 V
3. Thermal resistance (Tc = 25C)
Characteristics Junction to case thermal resistance Case to fin thermal resistance Symbol Rth (j-c) Rth (c-f) IGBT FRD Compound is applied Test Condition Min 3/4 3/4 3/4 Typ. 3/4 3/4 0.013 Max 0.033 0.068 3/4 C/W Unit C/W
5
2001-11-13
MIG400Q2CMB1X
Switching Time Test Circuit
Intelligent power module TLP559 VD 0.1 mF 15 kW OUT IN 15 V 68 mF GND VS C1
GND C2/E1 VCC
VD IF = 16 mA PG 15 V 68 mF GND 0.1 mF 15 kW OUT IN VS E2
GND
Timing Chart
Input pulse 15 V VIN Waveform 0
2.5 V
1.6 V
90% Irr IC Waveform Irr 90% trr 20% Irr
VCE Waveform
10% toff
10% tc (off)
10% ton
10% tc (on)
6
2001-11-13
MIG400Q2CMB1X
4. Recommended conditions for application
Characteristics Supply voltage Control supply voltage Carrier frequency Dead time Symbol VCC VD fc tdead Test Condition P-N power terminal VD-GND signal terminal PWM control Switching time test circuit (Note 2) Min 3/4 13.5 3/4 5 Typ. 600 15 3/4 3/4 Max 800 16.5 20 3/4 Unit V V kHz ms
Note 2: The table lists Dead time requirements for the module input, excluding photocoupler delays. When specifying dead time requirements for the photocoupler input, please add photocoupler delays to the dead time given above.
Dead Time Timing Chart
15 V VIN Waveform 0 15 V VIN Waveform 0 tdead tdead
7
2001-11-13
MIG400Q2CMB1X
IC - VCE
900 800 VD = 17 V 900 800
IC - VCE
VD = 17 V VD = 13 V
(A)
(A)
700 600 500 400 300 200 100 0 0 1 2 3 Common emitter Tj = 25C 4 5
700 600 500 400 300 200 100 0 0 1 2 3 Common emitter Tj = 125C 4 5 VD = 15 V VD = 13 V
IC
Collector current
VD = 15 V
Collector-emitter voltage
VCE
(V)
Collector current
IC
Collector-emitter voltage
VCE
(V)
Switching time - IC
10 10
Switching time - IC
ton
ton
(ms)
1
(ms)
toff tc (on) tc (off)
toff 1 tc (on) tc (off)
Switching time
0.1 Tj = 25C VCC = 600 V VD = 15 V L-LOAD 0.01 0 100 200 300 400 500
Switching time
0.1 Tj = 125C VCC = 600 V VD = 15 V L-LOAD 0.01 0 100 200 300 400 500
Collector current
IC
(A)
Collector current
IC
(A)
IF - VF
900 800 1000
trr, Irr - IF
Peak reverse recovery current Irr (A) Reverse recovery time trr ( 10 ns)
Irr
(A)
700 600 500 400 300 200 100 0 0 Common cathode : Tj = 25C : Tj = 125C 1 2 3 4
Forward current IF
100
10
trr
Common cathode : Tj = 25C : Tj = 125C 1 0 100 200 300 400 500
Forward voltage
VF (V)
Forward current
IF (A)
8
2001-11-13
MIG400Q2CMB1X
OC - Tc
1200 60
ID - fc
(A)
1000
(mA) ID Control circuit current
OC
50
Over current protection trip level
800
40
600
30
400
20
200 VD = 15 V 0 0
10 VD = 15 V Tj = 25C 0
25
50
75
100
125
150
0
5
10
15
20
25
Case temperature Tc
(C)
Carrier frequency fc (kHz)
Reverse bias SOA
Transient themal resistance Rth (t) (C/W)
720 1 0.3 0.1 0.03
Rth (t) - tw
OC
(A)
640
Diode stage
IC
480
Collector current
Transistor stage 0.01
320
0.003 0.001 Tc = 25C 0.0003 0.001 0.01
160
Tj < 125C = VD = 15 V 0 400 800 1200 1400
0
0.1
1
10
Collector-emitter voltage
VCE
(V)
Pulse width
tw (s)
Eon - IC
100 100
Eoff - IC
Eon (mJ)
10
(mJ) Turn off loss Eoff
VCC = 600 V VD = 15 V L-LOAD : Tj = 25C : Tj = 125C 100 200 300 400 500
10
Turn on loss
1
1 VCC = 600 V VD = 15 V L-LOAD : Tj = 25C : Tj = 125C 0 100 200 300 400 500
0.1 0
0.1
Collector current
IC
(A)
Collector current
IC
(A)
9
2001-11-13
MIG400Q2CMB1X
RESTRICTIONS ON PRODUCT USE
000707EAA
* TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. * The information contained herein is subject to change without notice.
10
2001-11-13

▲Up To Search▲

Price & Availability of MIG400Q2CMB1X

	To Download MIG400Q2CMB1X Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .